FTP: The first record located at the top of the header used to identify the file format.
VER: HYPACK version number.
INF: General survey information filled in by the data technician. . This typically contains the survey participants, the vessel name, other agencies involved with the survey, and the location of the survey. The three numbers at the end refer to initial tide correction at start-of-line, initial draft correction at start-of-line and sound velocity from the navigation parameters.. This information was not filled in correctly in 000_1141.150. All other files are correct.
FIL: Raw format file.
ELL: Ellipsoid information. The name of the ellipsoid followed by the semi-major axis in meters and the flattening ration.
PRO: Project information record where TME indicates Transverse Mercator and the central meridian of -81 indicates UTM, zone 17.
DTM: Datum transformation record
GEO: Geoid model. Blank if not present.
HVU: Horizontal and Vertical Units (meters).
TND: Survey time and date in UTC.
DEV 0: Indicated that the lines collected with device designation 0 are using DGPS receiver (CSI LGBX Pro)
OFF: device offsets (none used during this data collection) The number following OFF indicates which device
DEV 1: Indicates that lines collected with device designation 1 are referencing Furuno single-beam echo sounder
DEV 2: Indicates that lines collected with device designation 2 are using Ashtech Z-Extreme, capable of recording antenna elevations above a vertical datum (i.e. real-time kinematic, RTK)
DEV 3: Indicates that lines collected with device designation 3 are referencing Knudsen Chirp profiler
PRD: Private Device Data (disabled)
LIN 2: planned line data follows
PTS: planned line waypoints (eastings and northings, UTM, zone 17N, meters)
LBP: planned line begin point (easting and northings, UTM zone 17N, meters)
LNN X: planned line name, where X is the line number
EOL: end of planned line
EOH: end of header
The remaining elements have similar information in the first 3 columns. The first column will indicate the data type, the second column will indicate the device that recorded the information (e.g. 1 for Ashtech receiver) and the third column is the time tag (seconds past midnight) that is also sometimes referred to as the latency. The remaining information on each line is specific to the data type.
GYR: Gyro Data (Heading). Format GYR dn t h, where dn=device number, t=time tag (seconds past midnight), h=ship heading angle.
MSG: Message string in the format "MSG dn t message" where dn=device number; t=time tag (seconds past midnight); message is the message sent from the device.
EC1: echo sounding (singe frequency). Format EC1 dn t rd, where dn=device number, t=time tag (seconds past midnight), rd=raw depth.
POS: Position of the ship in the format "POS dn t x y" where dn=device number; t=time tag (seconds past midnight); x=easting; y=northing. On this cruise these values are in UTM, Zone 17, WGS84.
QUA: Position quality information in the format "QUA dn t n m h sat mode" where dn=device number; t=time tag (seconds past midnight); n=number of values to follow; m = 10 minus HDOP (horizontal dilution of precision); h=HDOP; sat=number of satellites; mode=GPS mode (NMEA 0183 standard values) where 0=fix not available or invalid; 1=GPS fix; 2=Differential GPS fix; 3=GPS PPS Mode fix; 4=RTK fix; 5=RTK float.
RAW: Position information in the format "RAW dn t n lat long alt utc" where dn=device number; t=time tag (seconds past midnight); n=number of values to follow; lat=raw latitude X 100; long=raw longitude X 100; alt=antenna altitude above ellipsoid (meters); utc=GPS time in the format HHMM.
FIX: Fix (event) mark. Format FIX vn, where n=FIX format version number, Always 2nd record in file.
The (National Marine Electronics Association) NMEA strings $GPGGA, $GPVTG, and $GPZDA are stored in the HYPACK file. These are defined as follows.
$GPGGA is GPS fix data in the format "$GPGGA, t, lat, lath, long, longh, q, sat, h, a, M, alt, M, t2, refcheck" where t=time in UTC in the format hhmmss.ss; lat=latitude in the format ddmm.mmmmmm; lath= N or S indicating the latitude hemisphere; long=longitude in the format dddmm.mmmmmm; longh=E or W indicating the hemisphere; q=fix quality where 0=fix not available or invalid; 1=GPS fix; 2=Differential GPS fix; 3=GPS PPS Mode fix; 4=RTK fix; 5=RTK float; sat=number of satellites; h=Horizontal Dilution of Precision (HDOP); a=Antenna altitude above mean sea level (geoid); M= units of antenna altitude in meters; alt=height of geoid above WGS84 ellipsoid; M=units of geoidal height in meters; t2=time since last DGPS update; refcheck=DGPS reference station id and the checksum.
Example: $GPGGA,163052.00,4118.964217,N,07036.966471,W,4,10,00.9,00005.332,M,-030.544,M,01,*57 UTC Time = 163052 Latitude = 4118.964217 N Longitude = 7036.966471 W Fix Quality = 4 Number of satellites = 10 HDOP = 00.9 relative accuracy of horizontal position Altitude = 5.332 meters above mean sea level Height of geoid above WGS84 ellipsoid = -30.554 meters Time since last update = 01 Checksum = *57.
$GPVTG is track made good and ground speed in the format $GPCTG, true, T, mag, M, grsp, N, grdp, K, mode, where t=true course made good over ground in degrees, T= True, m=magnetic course made good over ground in degrees, M=magnetic, gdsp=ground speed, N=Knots, grsp=ground speed, K=Kilometers per hour, mode=Mode indicator (A=Autonomous, D=Differential, E=Estimated, N=Data not valid).
Example: $GPVTG,089.23,T,104.82,M,004.86,N,009.02,K,D*28 True course made good: 089.23 Magnetic course made good: 104.82 Ground speed (knots) = 4.86 Ground speed (kilometers) = 9.02 Mode=Differential
$GPZDA is UTC Date/Time and Local Time Zone Offset in the format $GPZDA,hhmmss.ss,xx,xx,xxxx,xx,xx where hhmmss.ss=UTC, xx=Day, 01 to 31, xx=month, 01 to 12, xxx=Year, xx=Local zone description, 00 to +/- 13 hours, xx=Local zone minutes description (same sign as hours), checksum.
Example: $GPZDA,163053.00,09,08,2007,,*60 UTC= 163053.00 UTC day = 09 UTC month = 08 UTC year = 2007 Local zone hours = null Local zone minutes = null Checksum = *60
Any use of trade, product, or firm names is for descriptive purposes only and does not imply endorsement by the U.S. Government.